Newest Post

Archive for 2016

Readmore


Pertama konfigurasi switch terlebih dahulu
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 100
Switch(config-vlan)#name ppic
Switch(config-vlan)#vlan 200
Switch(config-vlan)#name marketing
Switch(config-vlan)#vlan 300
Switch(config-vlan)#name produksi
Switch(config-vlan)#ex
Switch(config)#int fa0/2
Switch(config-if)#switchport access vlan 100
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/3
Switch(config-if)#switchport access vlan 100
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/4
Switch(config-if)#switchport access vlan 100
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/5
Switch(config-if)#switchport access vlan 200
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/6
Switch(config-if)#switchport access vlan 200
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/7
Switch(config-if)#switchport access vlan 200
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/8
Switch(config-if)#switchport access vlan 300
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/9
Switch(config-if)#switchport access vlan 300
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/10
Switch(config-if)#switchport access vlan 300
Switch(config-if)#switchport mode access
Switch(config-if)#ex
Switch(config)#int fa0/1
Switch(config-if)#switchport mode trunk
Switch(config-if)#ex
Switch(config)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Lanjut konfigurasi router
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int fa0/0.100
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.100, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.100, changed state to up

Router(config-subif)#encapsulation dot1Q 100
Router(config-subif)#ip add 172.10.10.1 255.255.255.0
Router(config-subif)#int fa0/0.200
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.200, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.200, changed state to up

Router(config-subif)#encapsulation dot1Q 200
Router(config-subif)#ip add 172.10.20.1 255.255.255.0
Router(config-subif)#int fa0/0.300
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.300, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.300, changed state to up

Router(config-subif)#encapsulation dot1Q 300
Router(config-subif)#ip add 172.10.30.1 255.255.255.0
Router(config-subif)#ex
Router(config)#int fa0/0.100
Router(config-subif)#ip dhcp pool tkj
Router(dhcp-config)#int fa0/0.100
Router(config-subif)#ip dhcp pool ppic
Router(dhcp-config)#network 172.10.10.0 255.255.255.0
Router(dhcp-config)#default-router 172.10.10.1
Router(dhcp-config)#dns-server 8.8.8.8
Router(dhcp-config)#ip dhcp excluded-add 172.10.10.1 172.10.10.2
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0.200
Router(config-subif)#ip dhcp pool marketing
Router(dhcp-config)#network 172.10.20.0 255.255.255.0
Router(dhcp-config)#default-router 172.10.20.1
Router(dhcp-config)#dns-server 8.8.8.8
Router(dhcp-config)#ip dhcp excluded-add 172.10.20.1 172.10.20.2
Router(config)#int fa0/0.300
Router(config-subif)#ip dhcp pool produksi
Router(dhcp-config)#network 172.10.30.0 255.255.255.0
Router(dhcp-config)#default-router 172.10.30.1
Router(dhcp-config)#dns-server 8.8.8.8
Router(dhcp-config)#ip dhcp excluded-add 172.10.30.1 172.10.30.2
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console

Setelah konfigurasi, langsung ke pc dan hidupkan DHCP
Hasil:


Konfigurasi telah selesai terima kasih :)

DHCP ON ROUTER

Monday, October 31, 2016
Add Comments
Readmore


Konfigurasi switch:

Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 100
Switch(config-vlan)#name ppic
Switch(config-vlan)#vlan 200
Switch(config-vlan)#name marketing
Switch(config-vlan)#vlan 300
Switch(config-vlan)#name produksi
Switch(config-vlan)#ex
Switch(config)#int fa0/1
Switch(config-if)#switchport access vlan 100
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/2
Switch(config-if)#switchport access vlan 100
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/3
Switch(config-if)#switchport access vlan 100
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/4
Switch(config-if)#switchport access vlan 200
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/5
Switch(config-if)#switchport access vlan 200
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/6
Switch(config-if)#switchport access vlan 200
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/7
Switch(config-if)#switchport access vlan 300
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/8
Switch(config-if)#switchport access vlan 300
Switch(config-if)#switchport mode access
Switch(config-if)#int fa0/9
Switch(config-if)#switchport access vlan 300
Switch(config-if)#switchport mode access
Switch(config-if)#ex
Switch(config)#int vlan 100
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan100, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to up

Switch(config-if)#ip add 172.20.10.1 255.255.255.0
Switch(config-if)#int vlan 200
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan200, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan200, changed state to up

Switch(config-if)#ip add 172.20.20.1 255.255.255.0
Switch(config-if)#int vlan 300
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan300, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan300, changed state to up

Switch(config-if)#ip add 172.20.30.1 255.255.255.0
Switch(config-if)#ex
Switch(config)#ip routing
Switch(config)#
Switch(config)#ex
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#ip dhcp pool vlan100
Switch(dhcp-config)#network 172.20.10.0 255.255.255.0
Switch(dhcp-config)#default-router 172.20.10.1
Switch(dhcp-config)#dns-server 8.8.8.8
Switch(dhcp-config)#ip dhcp pool vlan200
Switch(dhcp-config)#network 172.20.20.0 255.255.255.0
Switch(dhcp-config)#default-router 172.20.20.1
Switch(dhcp-config)#dns-server 8.8.8.8
Switch(dhcp-config)#ip dhcp pool vlan300
Switch(dhcp-config)#network 172.20.30.0 255.255.255.0
Switch(dhcp-config)#default-router 172.20.30.1
Switch(dhcp-config)#dns-server 8.8.8.8
Switch(dhcp-config)#ex

Hasil :





konfigurasi telah selesai terima kasih :)

Dhcp switch layer 3

Add Comments
Readmore


konfigurasi router 1
 
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.10.10.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#int fa0/1
Router(config-if)#ip add 30.30.30.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#ex
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config)#router ospf 1
Router(config-router)#network 10.10.10.0 0.0.0.3 area 10
Router(config-router)#network 30.30.30.0 0.0.0.255 area 10
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#
01:03:51: %OSPF-5-ADJCHG: Process 1, Nbr 40.40.40.1 on FastEthernet0/0 from LOADING to FULL, Loading Do





konfiguurasi router 2:

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.10.10.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int fa0/1
Router(config-if)#ip add 20.20.20.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#int fa1/0
Router(config-if)#ip add 40.40.40.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ex
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config)#router ospf 1
Router(config-router)#network 10.10.10.0 0.0.0.3 area 10
Router(config-router)#network 20.20.20.0 0.0.0.3 area 20
Router(config-router)#network 40.40.40.0 0.0.0.255 area 0
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#
00:52:53: %OSPF-5-ADJCHG: Process 1, Nbr 50.50.50.1 on FastEthernet0/1 from LOADING to FULL, Loading Done





konfigurasi router 3:

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 20.20.20.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#int fa0/1
Router(config-if)#ip add 50.50.50.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#ex
Router(config)#router ospf 1
Router(config-router)#network 20.20.20.0 0.0.0.3 area 20
Router(config-router)#network 20.20.50.0 0.0.0.255 area 20
01:05:42: %OSPF-5-ADJCHG: Process 1, Nbr 40.40.40.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
Router(config-router)#network 50.50.50.0 0.0.0.255 area 2
Router(config-router)#do wr
Building configuration...
[OK]
Router(config-router)#ex
Router(config)#router ospf 1
Router(config-router)#network 20.20.20.0 0.0.0.3 area 20
Router(config-router)#network 50.50.50.0 0.0.0.255 area 20
Router(config-router)#
01:11:32: %OSPF-6-AREACHG: 50.50.50.0/0 changed from area 2 to area 20

Router(config-router)#do wr
Building configuration...
[OK]

hasil ping:
terima kasih semoga bermanfaat :)

ROUTING OSPF Multi Area

Add Comments

Beberapa faktor kunci pengendali dan pengukuran kriteria e-commerce

Kunci Pengedali dan Pengukuran Kriteria e-commerce jika dilihat dari faktor: •Faktor Teknologi •Faktor Politik •Faktor Sosial •Faktor E...

// Copyright © Ilmu Informatika //Anime-Note//Powered by Blogger // Designed by Johanes Djogan //