Newest Post
// On :Wednesday, October 26, 2016
pertama yaitu konfigurasi router 1 terlebih dahulu :
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname nia
nia(config)#int gi0/0
nia(config-if)#ip add 10.10.10.1 255.255.255.0
nia(config-if)#no sh
nia(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
nia(config-if)#ex
nia(config)#int gi0/1
nia(config-if)#ip add 30.30.30.1 255.255.255.0
nia(config-if)#no sh
nia(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
nia(config-if)#do wr
Building configuration...
[OK]
nia(config)#router ospf 1
nia(config-router)#network 10.10.10.0 0.0.0.255 area 0
nia(config-router)#network 30.30.30.0 0.0.0.255 area 0
nia(config-router)#do wr
Building configuration...
[OK]
lanjut ke router 2:
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname nia
nia(config)#int gi0/0
nia(config-if)#ip add 10.10.10.2 255.255.255.0
nia(config-if)#no sh
nia(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
nia(config-if)#ex
nia(config)#int gi0/1
nia(config-if)#ip add 20.20.20.1 255.255.255.0
nia(config-if)#no sh
nia(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
nia(config-if)#ex
nia(config)#int gi0/2
nia(config-if)#ip add 40.40.40.1 255.255.255.0
nia(config-if)#no sh
nia(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to up
nia(config-if)#do wr
Building configuration...
[OK]
nia(config-if)#router ospf 1
nia(config-router)#network 40.40.40.0 0.0.0.255 area 0
nia(config-router)#network 10.10.10.0 0.0.0.255 area 0
nia(config-router)#network 20.20.20.0 0.0.0.255 area 0
00:30:06: %OSPF-5-ADJCHG: Process 1, Nbr 30.30.30.1 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
nia(config-router)#do wr
Building configuration...
[OK]
lanjut ke router 3
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname melli
melli(config)#int gi0/0
melli(config-if)#ip add 20.20.20.2 255.255.255.0
melli(config-if)#no sh
melli(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
melli(config-if)#ex
melli(config)#int gi0/1
melli(config-if)#ip add 50.50.50.1 255.255.255.0
melli(config-if)#no sh
melli(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
melli(config-if)#router ospf 1
melli(config-router)#network 50.50.50.0 0.0.0.255 area 0
melli(config-router)#network 20.20.20.0 0.0.0.255 area 0
melli(config-router)#do wr
Building configuration...
[OK]
Telah selesai konfigurasi ketiga router, sekarang berikan IP Adress pada PC0, PC1 dan PC2
PC0:
PC2:
Setelah selesai konfigurasi router dan memberikan IP Address pada PC, lalu kita coba ping!!!
dan lihat apakah hasilnya Reply atau RTO ,, jika Reply berarti berhasil, Jika RTO tidak berhasil,,,
Dan hasilnya Reply... Konfigurasi telah selesai terima kasih... :)
